FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   - 3.3. Engine V6
      3.3.1. A technical characteristics
      3.3.2. The repair which is not demanding removal of the engine
      3.3.3. Engine removal
      - 3.3.4. Dismantling and check of details of the engine
         3.3.4.1. Engine dismantling
         3.3.4.2. Check of degree of deterioration of details of the engine
         3.3.4.3. Axis knot коромысел
         3.3.4.4. Pushers of valves and a bar of pushers
         3.3.4.5. A camshaft
         3.3.4.6. Heads of the block of cylinders
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and piston rings
         3.3.4.9. Piston fingers and rods
         3.3.4.10. A cranked shaft
         3.3.4.11. Radical and шатунные bearings
         3.3.4.12. Distributive gear wheels
         3.3.4.13. A flywheel
         + 3.3.4.14. Greasing system
         3.3.4.15. Ventilation system картера
         - 3.3.4.16. Engine assemblage
            3.3.4.16.1. Installation of a cranked shaft
            3.3.4.16.2. Camshaft installation
            3.3.4.16.3. Installation of pistons and rods
            3.3.4.16.4. Installation of the oil pump
            3.3.4.16.5. Flywheel installation
            3.3.4.16.6. Installation of a gear wheel and a cover of a drive of the distributive mechanism
            3.3.4.16.7. Installation of the oil pallet, the water pump and a pulley коленвала
            3.3.4.16.8. Removal and installation of the oil heat exchanger
            3.3.4.16.9. Heads of the block of cylinders, axes коромысел and an inlet collector
         3.3.4.17. Adjustment of backlashes of valves
         3.3.4.18. Auxiliary details of the engine
         3.3.4.19. Engine installation
         3.3.4.20. Start of the engine after major repairs or restoration
      + 3.3.5. Changes in a design of engines V6 2,4 and 2,9 дм3
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


b087f616

3.3.4.16.8. Removal and installation of the oil heat exchanger
THE GENERAL DATA

The oil heat exchanger

1 – the carving plug,

2 – a lining,

3 – the heat exchanger,

4 – an adapter,

5 – the oil filter

The oil heat exchanger is established between the oil filter and the block of cylinders.

PERFORMANCE ORDER
1. Before heat exchanger removal it is necessary to remove the oil filter at first. To disconnect hoses of the heat exchanger and to muffle their stoppers.
2. Flat-nose pliers to turn off an adapter. To remove the heat exchanger and its lining. If the plug acts in film or leaves together with an adapter – it is necessary to replace the plug.
3. Assemblage begins with installation of the new plug in the block of cylinders. To put on a carving of the plug and an internal part of an adapter hermetic.
4. To put on an initial carving of the plug a hermetic drop since otherwise surpluses of hermetic can get to greasing system.
5. To establish a new lining and the heat exchanger, to fix its adapter. To be convinced that heat exchanger tubes are established under a corresponding corner, and to tighten an adapter the corresponding moment of an inhaling (And – the back party of the block of cylinders of the engine).
6. To establish the new oil filter.