FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   - 3.3. Engine V6
      3.3.1. A technical characteristics
      3.3.2. The repair which is not demanding removal of the engine
      3.3.3. Engine removal
      - 3.3.4. Dismantling and check of details of the engine
         3.3.4.1. Engine dismantling
         3.3.4.2. Check of degree of deterioration of details of the engine
         3.3.4.3. Axis knot коромысел
         3.3.4.4. Pushers of valves and a bar of pushers
         3.3.4.5. A camshaft
         3.3.4.6. Heads of the block of cylinders
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and piston rings
         3.3.4.9. Piston fingers and rods
         3.3.4.10. A cranked shaft
         3.3.4.11. Radical and шатунные bearings
         3.3.4.12. Distributive gear wheels
         3.3.4.13. A flywheel
         + 3.3.4.14. Greasing system
         3.3.4.15. Ventilation system картера
         - 3.3.4.16. Engine assemblage
            3.3.4.16.1. Installation of a cranked shaft
            3.3.4.16.2. Camshaft installation
            3.3.4.16.3. Installation of pistons and rods
            3.3.4.16.4. Installation of the oil pump
            3.3.4.16.5. Flywheel installation
            3.3.4.16.6. Installation of a gear wheel and a cover of a drive of the distributive mechanism
            3.3.4.16.7. Installation of the oil pallet, the water pump and a pulley коленвала
            3.3.4.16.8. Removal and installation of the oil heat exchanger
            3.3.4.16.9. Heads of the block of cylinders, axes коромысел and an inlet collector
         3.3.4.17. Adjustment of backlashes of valves
         3.3.4.18. Auxiliary details of the engine
         3.3.4.19. Engine installation
         3.3.4.20. Start of the engine after major repairs or restoration
      + 3.3.5. Changes in a design of engines V6 2,4 and 2,9 дм3
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


b087f616

3.3.4.16.6. Installation of a gear wheel and a cover of a drive of the distributive mechanism
PERFORMANCE ORDER
1. To establish a new sealing ring in a drive cover.
2. To check up шпоночные flutes on the end of a cranked shaft, they should be pure, on шпонках should not be an agnail. To establish шпонки in шпоночные flutes.
3. If the gear wheel of a cranked shaft acted in film, to establish it into place so that a gear wheel was up to the end established on a cranked shaft, thus it is possible to take advantage of a pipe of suitable diameter. For pressing it also it is possible to use a pulley and a bolt temporarily.
4. To establish a camshaft gear wheel on a shaft so that a label a core it was combined with a label on a gear wheel of a cranked shaft. Pay attention that on a gear wheel коленвала there are two labels, made a core, it is necessary to achieve coincidence to the necessary label. Thus шпоночные grooves are turned to each other. On later 2,4 and 2,8 дм3 engines the nylon gear wheel of a camshaft is established.
5. To establish a washer and a bolt of a gear wheel of a camshaft. To tighten a bolt according to the inhaling moment.
6. To clear a forward surface of an intermediate plate and an interfaced surface of a cover of a drive, then on both interfaced surfaces to put hermetic.
7. To establish on an intermediate plate a new lining and to establish a cover of a drive of the distributive mechanism on the block of cylinders.
8. To establish fixing bolts of a cover of a drive and to tighten them according to the inhaling moment.
9. To check up axial люфт a camshaft.
10. To define position of a sealing ring in a cover of the distributive mechanism, then to squeeze out old consolidation.
11. To clear a forward plane of a transitive plate and a plane of a cover of the distributive mechanism, then to cover both surfaces with hermetic.
12. To place on a transitive plate a new lining and to establish a cover of the distributive mechanism on the block of cylinders. To wrap bolts manually.
13. Having taken advantage of a calliper, to centre a cover of the distributive mechanism concerning a camshaft, up to the end to tighten bolts.
14. Establish a sealing ring on a cover of the distributive mechanism, and to insert it into place, by means of the plug and a bolt.
15. Remove ledges of a lining from connected surfaces oil картера.