FORD SCORPIO

1985-1994 of release

Repair and car operation


Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   - 3.3. Engine V6
      3.3.1. A technical characteristics
      3.3.2. The repair which is not demanding removal of the engine
      3.3.3. Engine removal
      - 3.3.4. Dismantling and check of details of the engine
         3.3.4.1. Engine dismantling
         3.3.4.2. Check of degree of deterioration of details of the engine
         3.3.4.3. Axis knot коромысел
         3.3.4.4. Pushers of valves and a bar of pushers
         3.3.4.5. A camshaft
         3.3.4.6. Heads of the block of cylinders
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and piston rings
         3.3.4.9. Piston fingers and rods
         3.3.4.10. A cranked shaft
         3.3.4.11. Radical and шатунные bearings
         3.3.4.12. Distributive gear wheels
         3.3.4.13. A flywheel
         + 3.3.4.14. Greasing system
         3.3.4.15. Ventilation system картера
         + 3.3.4.16. Engine assemblage
         3.3.4.17. Adjustment of backlashes of valves
         3.3.4.18. Auxiliary details of the engine
         3.3.4.19. Engine installation
         3.3.4.20. Start of the engine after major repairs or restoration
      + 3.3.5. Changes in a design of engines V6 2,4 and 2,9 дм3
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


b087f616

3.3.4.11. Radical and шатунные bearings
THE GENERAL DATA

The firm core Plastigage used for measurement of backlashes in radical and шатунных bearings

Measurement of width of core Plastigage by a scale ruler for definition of size of a backlash

At qualitative service and regular replacement of oil and oil filters bearings serve very long. A damage sign шатунных bearings is regular rhythmical loud knock from outside a cranked shaft. Frequency depends on engine turns. Especially this knock is swept up, when the engine works under loading. This sign is accompanied by oil pressure drop though usually it is imperceptible if the gauge of pressure of oil is not established. Appreciable vibration usually specifies in damage of the radical bearing, especially on the big turns of the engine, and this vibration is accompanied by more essential pressure drop of oil and "roaring" noise.

At loose leaves of bearings in a good condition the surface smooth, has a homogeneous matte-silver-grey colouring on all surface. The worn out loose leaves have sites with a various colouring there where metal has worn out, and the substrate has seemed. The damaged loose leaves have scratches or teases. If a cranked shaft in a good condition to deal with a question simply, having got other set of bearings of the same size. If repolishing or replacement of a cranked shaft is spent, at this operation it is required to replace and loose leaves of bearings.

Original коленвал in the block of cylinders can have the standard or first repair size, in the latter case in it specify covers of bearings which are marked by a white paint.

On engines in volume 2,8 дм3 both radical necks, and necks шатунных bearings have only the standard sizes.

The available backlash in bearings can be checked up with use of the firm tool, cores Plastigage. The piece of core Plastigage settles down on a neck of a cranked shaft, then the loose leaf of the bearing and a cover gathers, bolts and nuts are tightened by the moment specified in subsection 3.3.1. After cover removal the width of a core is measured by a scale ruler which specifies the size of a backlash at present.