FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   - 3.3. Engine V6
      3.3.1. A technical characteristics
      3.3.2. The repair which is not demanding removal of the engine
      3.3.3. Engine removal
      - 3.3.4. Dismantling and check of details of the engine
         3.3.4.1. Engine dismantling
         3.3.4.2. Check of degree of deterioration of details of the engine
         3.3.4.3. Axis knot коромысел
         3.3.4.4. Pushers of valves and a bar of pushers
         3.3.4.5. A camshaft
         3.3.4.6. Heads of the block of cylinders
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and piston rings
         3.3.4.9. Piston fingers and rods
         3.3.4.10. A cranked shaft
         3.3.4.11. Radical and шатунные bearings
         3.3.4.12. Distributive gear wheels
         3.3.4.13. A flywheel
         + 3.3.4.14. Greasing system
         3.3.4.15. Ventilation system картера
         - 3.3.4.16. Engine assemblage
            3.3.4.16.1. Installation of a cranked shaft
            3.3.4.16.2. Camshaft installation
            3.3.4.16.3. Installation of pistons and rods
            3.3.4.16.4. Installation of the oil pump
            3.3.4.16.5. Flywheel installation
            3.3.4.16.6. Installation of a gear wheel and a cover of a drive of the distributive mechanism
            3.3.4.16.7. Installation of the oil pallet, the water pump and a pulley коленвала
            3.3.4.16.8. Removal and installation of the oil heat exchanger
            3.3.4.16.9. Heads of the block of cylinders, axes коромысел and an inlet collector
         3.3.4.17. Adjustment of backlashes of valves
         3.3.4.18. Auxiliary details of the engine
         3.3.4.19. Engine installation
         3.3.4.20. Start of the engine after major repairs or restoration
      + 3.3.5. Changes in a design of engines V6 2,4 and 2,9 дм3
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


b087f616

3.3.4.16.7. Installation of the oil pallet, the water pump and a pulley коленвала
THE GENERAL DATA

Sequence of a tightening of bolts of fastening of the pallet картера


PERFORMANCE ORDER
1. To clear contact surfaces картера and the pallet. The flutes which are available in holders of consolidations, should be pure.
2. To establish rubber consolidations in flutes of holders.
3. To put on flutes a layer of hermetic and to establish lining uvulas in grooves of rubber consolidations.
4. To watch that apertures in a lining have coincided with apertures on a contact surface картера. To establish into place the pallet, to watch that the lining was not displaced.
5. To establish fixing bolts of the pallet and to tighten them in two steps according to the inhaling moments.
6. To establish a new lining on a cover of a drive and to establish the water pump. To establish the thermostat and the thermostat case. To connect a back branch pipe of a water highway.
7. To put on a pulley washer коленвала hermetic. Establish a pulley, a washer and a fixing bolt. Tighten a bolt according to the inhaling moment.
8. To establish all connections and gauges of the control of pressure of oil.
9. To put on bypass a hose a back branch pipe of the pump of a cooling liquid.
10. If it is provided by a design, to place on the block of cylinders the oil heat exchanger together with new consolidation, then to insert the plug and to tighten it so that heat exchanger tubes have been turned under the necessary corner.