FORD SCORPIO

1985-1994 of release

Repair and car operation

Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   + 3.3. Engine V6
   + 3.4. Ignition and engine management systems
   - 3.5. Diesel engines
      3.5.1. A technical characteristics
      3.5.2. The repair which is not demanding removal of the engine
      3.5.3. Check and adjustment of backlashes of valves
      + 3.5.4. Fuel system
      + 3.5.5. A head of the block of cylinders
      3.5.6. Removal and engine installation
      - 3.5.7. Dismantling, repair and engine assemblage
         3.5.7.1. Dismantling
         - 3.5.7.2. Engine assemblage
            3.5.7.2.1. Installation of the back radical bearing
            3.5.7.2.2. Installation of lateral sealants
            3.5.7.2.3. Assemblage of knot the piston-rod
            3.5.7.2.4. Selection of pistons for diameter of the cylinder
            3.5.7.2.5. Assemblage of a drive of system timing
            3.5.7.2.6. The further actions on engine assemblage
      3.5.8. Турбокомпрессор
      + 3.5.9. Greasing system
      + 3.5.10. Cooling system
      3.5.11. Typical malfunctions of the engine
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment

3.5.7.2.6. The further actions on engine assemblage

PERFORMANCE ORDER

1. To establish a pulley of a cranked shaft.

2. To eliminate traces of oil or greasing on a bolt of fastening of a pulley of a cranked shaft, a washer and from a surface of connection of a pulley and a washer.

3. To put 3 drops of glue Frenetanch on a carving in an aperture of a cranked shaft.

4. To tighten a bolt of fastening of a pulley of a cranked shaft the corresponding moment.

5. To establish a head of the block of cylinders of the engine (subsection 3.5.5.2 see).

6. To establish coupling (subsection 6.2.3 see).

7. To establish the fuel pump and to adjust the injection moment.

8. To establish:
     – A cover of a head of the block of cylinders together with a new lining (a lining to paste to a cover to tighten nuts the moment of 3 Nanometers);
     – The thermostat of a regulator of the raised number of turns of the cold engine together with a new copper lining and to tighten its moment of 22,5 Nanometers;
     – Candles накаливания, their electric wire and токовую the tyre; candles to tighten the moment of 50 Nanometers;
     – The pipeline of giving of fuel;
     – The generator together with the holder of the tension device;
     – The holder of the oil filter together with a new lining;
     – The pipeline of giving of oil to an axis of levers of valves.

9. To attach a forward exhaust pipe to a final collector.

10. To establish tension devices клиновых belts, the auxiliary pump of system of a steering, the vacuum pump and the radiator fan.

11. To put on and pull клиновые belts.

12. To measure a backlash of a drive of the oil pump.

home