Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
+ 3.1. Engine OHC
+ 3.2. Engine DOHC
+ 3.3. Engine V6
+ 3.4. Ignition and engine management systems
- 3.5. Diesel engines
3.5.1. A technical characteristics
3.5.2. The repair which is not demanding removal of the engine
3.5.3. Check and adjustment of backlashes of valves
+ 3.5.4. Fuel system
+ 3.5.5. A head of the block of cylinders
3.5.6. Removal and engine installation
- 3.5.7. Dismantling, repair and engine assemblage
3.5.7.1. Dismantling
- 3.5.7.2. Engine assemblage
3.5.7.2.1. Installation of the back radical bearing
3.5.7.2.2. Installation of lateral sealants
3.5.7.2.3. Assemblage of knot the piston-rod
3.5.7.2.4. Selection of pistons for diameter of the cylinder
3.5.7.2.5. Assemblage of a drive of system timing
3.5.7.2.6. The further actions on engine assemblage
3.5.8. Турбокомпрессор
+ 3.5.9. Greasing system
+ 3.5.10. Cooling system
3.5.11. Typical malfunctions of the engine
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment
|
System timing
1 – a casing приводной system chains timing,
2 – a lining of a casing,
3 – an intermediate plate,
4 – a lining of a plate,
5 – an asterisk of a cam-shaft,
6 – a system chain timing,
7 – an asterisk of the tension device of a chain,
8 – the ball bearing,
9 – the clown,
10 – the plug,
11 – a toddler,
12 – an axis of levers of valves,
13 – the holder of an axis of levers of valves,
14 – the lever of the valve,
15 – the holder of blocking of an axis of levers of valves, |
16 – an adjusting spring of an axis of levers of valves,
17 – flat washers,
18 – a pusher,
19 – a core of a pusher,
20 – the final valve,
21 – the inlet valve,
22 – crackers of fastening of a basic plate of a spring of the valve,
23 – the top basic plate of a spring of the valve,
24 – a spring of the valve,
25 – the bottom basic plate of a spring of the valve,
26 – a sealant of a core of the valve |
The krivoshipno-shatunnyj mechanism
1 – a cranked shaft,
2 – a pulley,
3 – an asterisk,
4 – a sealing ring,
5 – the aligning plug of a primary shaft of a transmission,
6 – a flywheel,
7 – a washer of fixation of bolts of fastening of a flywheel,
8 – loose leaves of radical bearings,
9 – persistent half rings of a cranked shaft, |
10 – уплотнители the back radical bearing,
11 – a bolt of a rod,
12 – a rod,
13 – the plug of a head of a rod,
14 – the loose leaf шатунного the bearing,
15 – the piston,
16 – a piston finger,
17 – маслосъемное a ring,
18 – a bottom sealing ring,
19 – the top sealing ring (компрессионное) |
At correct installation of an asterisk on a cranked shaft the sign (1) should be visible
Adjusting signs on asterisks and приводной system chains timing
Tension приводной system chains timing
Removal of the tension device приводной system chains timing
| PERFORMANCE ORDER |
| 1. To establish (the party with an adjusting sign outside) a chain asterisk together with шпонкой on a cranked shaft. |
| 2. To establish a flange of the holder of an asterisk of a drive of the fuel pump together with the pipeline of giving of oil. |
| 3. To establish the tension device приводной system chains timing. |
| 4. To establish an asterisk of a drive of the fuel pump and to turn a cranked shaft so that the piston in 1st cylinder was in ВМТ. |
| 5. To establish приводную a system chain timing so that its designations of red colour coincided with signs on asterisks of a cam-shaft and the fuel pump, and a designation of white colour – with signs on an asterisk of a cranked shaft. |
| 6. To establish an asterisk of the tension device of a chain together with the clown and to pull a chain so that to receive a backlash of 0,5-1 mm between a cheek of the tension device and its holder. To tighten a roller of the tension device. |
| 7. To replace a sealing ring of a casing приводной system chains timing and to screw a casing. |
|
|
|
