+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
- 3.1. Engine OHC
3.1.1. A technical characteristics
- 3.1.2. Service and repair
220.127.116.11. Engine adjustment
- 18.104.22.168. The repair which is not demanding removal of the engine
22.214.171.124.1. Removal and installation of a gear belt
126.96.36.199.2. Removal of a head of the block of cylinders
188.8.131.52.3. Dismantling and assemblage of a head of the block of cylinders
184.108.40.206.4. Installation of a head of the block of cylinders
220.127.116.11.5. Removal and installation of the oil pallet
18.104.22.168.6. Replacement of a forward sealing ring of a cranked shaft
22.214.171.124.7. Replacement of a back sealing ring of a cranked shaft
126.96.36.199.8. Replacement of support of the engine
188.8.131.52. Removal and engine installation
+ 184.108.40.206. Engine repair
220.127.116.11. Greasing system
18.104.22.168. Ventilation system картера
+ 3.2. Engine DOHC
+ 3.3. Engine V6
+ 3.4. Ignition and engine management systems
+ 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment
Knot of a head of the block of cylinders
|1 – a cover of a head of the block of cylinders,
2 – clamping plates,
3 – a lining of a cover,
4 – a camshaft,
5 – an adjusting plate of a camshaft,
6 – a bolt of fastening of a head,
7 – a spring of the lever of the valve,
8 – the lever of the valve,
9 – a bolt with a spherical tip (a support of the lever of the valve),
10 – crackers,
|11 – a plate of a spring,
12 – the directing plug,
14 – the valve,
15 – plugs of bearings of a camshaft,
16 – the pipeline of giving of oil to bearings of a camshaft,
17 – a lining of a head of the block of cylinders,
18 – a head of the block of cylinders,
19 – a sealing ring of a camshaft
Knot of the air filter
1 – the case,
2 – a cover,
3 – a filtering element,
4 – the goffered hose of an air inlet,
5 – an air inlet of warm air
| PERFORMANCE ORDER
| 1. To disconnect from the accumulator a weight wire.
| 2. To merge cooling liquid from cooling system.
| 3. To remove the air filter, to disconnect pipelines and draughts from the carburettor and an inlet collector.
|4. To disconnect electric wires from the carburettor and a head of the block of cylinders.
|5. To disconnect from spark plugs of a wire of a high voltage and to remove the high voltage distributor.
|6. To disconnect pipelines of a cooling liquid from the chamber of the starting arrangement of the carburettor, the top hose from a radiator, and also a hose of a broad tank from a head of the block of cylinders.
|7. To disconnect a reception exhaust pipe from a final collector (3 nuts).
|8. To remove a protective casing of a gear belt of system timing (3 bolts), and also a cover of a head of the block of cylinders (10 bolts) together with its sealant.
|9. To establish the piston of 1 cylinder in the top dead point, turning a cranked shaft for a bolt, крепящий a pulley клинового a belt, in a direction of working rotation until the label of the top dead point will not be combined with a label on a casing of a forward sealing ring of a cranked shaft, and the label on a cam-shaft pulley will not be combined with a label on a head of the block of cylinders. To note position of a rotor of the distributor in relation to the distributor case for what to uncover the distributor having raised a screw-driver 2 lateral fixing скобы and having unscrewed 2 screws of fastening of a cover.
|10. To unscrew fastening of the tension device of a gear belt of system timing (the adaptation 21.012) to weaken it and to tighten in this position.
|11. To remove a gear belt of system timing.
|12. To unscrew spark plugs, and also to unscrew bolts of a head of the block of cylinders (the adaptation 21.002) in sequence opposite to their tightening.
|13. To remove a head of the block of cylinders from the block of cylinders of the engine.
It is not necessary to have a head of the block of cylinders the bottom plane on a horizontal surface as it threatens with damage of valves acting below a plane. A head of the block of cylinders it is necessary to have on two wooden брусках so that plates of valves concerned nothing.