FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
- 5. Fuel system
   5.1. A technical characteristics
   5.2. Fuel
   5.3. Neetilirovannyj gasoline of engines V6, 2.4 and 2.9 дм3
   + 5.4. System of giving of air
   - 5.5. Carburettor PIERBURG
      5.5.1. Adjustment of turns of idling and quality of a mix
      5.5.2. Adjustment демпфера throttle заслонки the first chamber
      5.5.3. Adjustment of a starting backlash air заслонки
      5.5.4. Removal and carburettor installation
      5.5.5. Carburettor dismantling
      5.5.6. Carburettor assemblage
      5.5.7. Adjustment of fast idling
      5.5.8. Carburettor Pierburg changes 2V since September 1986 г
   + 5.6. Carburettor WEBER 2V
   + 5.7. Carburettor WEBER 2V TLD
   + 5.8. System of injection of fuel
   5.9. Removal and installation of an inlet collector
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


b087f616

5.5.5. Carburettor dismantling
THE GENERAL DATA

Removal of the vacuum device air заслонки

1 – a stopper,

2 – screws

Removal of knot of a vacuum diaphragm of the starting arrangement

The clip (it is specified by an arrow) should be wrung out.

Fuel tube

The fuel tube (it is specified by an arrow) should enter in эмульсионный a well.

PERFORMANCE ORDER
1. To remove the carburettor from the engine.
2. Carefully to clear the carburettor outside.
3. To unscrew five screws (on latest models – four) fastenings of a cover of the carburettor (1 – screws of fastening of the carburettor, 2 – screws of fastening of a cover).
4. To uncover the carburettor having paid attention to connection of a cam of fast idling and the throttle lever.
5. To remove the rests of fuel from поплавковой chambers.
6. If necessary to unscrew the main jets and an idling jet.
7. If the float or the needle valve act in film, they cannot be reused, and it is necessary to establish new details.
8. To unscrew a tube of giving of fuel with the filter.
9. To unscrew three screws of fastening скобы демпфера throttle заслонки the first chamber. Not to remove демпфер throttle заслонки the first chamber with скобы if its replacement is not required.
10. To unscrew two screws of fastening and, having wrung out the ball hinge, to remove vacuum knot.
11. To unscrew three screws of fastening of a cover of the pump.
12. To uncover, a diaphragm, a spring, a washer and a shutter. To note shutter orientation.
13. To unscrew two screws of fastening and to remove эконостат.
14. To remove the rests of fuel from поплавковой chambers.
15. If necessary to unscrew the main jets and an idling jet.
16. If the float or the needle valve act in film, they cannot be reused, and it is necessary to establish new details.
17. To unscrew a tube of giving of fuel with the filter.
18. To unscrew three screws of fastening скобы демпфера throttle заслонки the first chamber. Not to remove демпфер throttle заслонки the first chamber with скобы if its replacement is not required.
19. To unscrew two screws of fastening and, having wrung out the ball hinge, to remove vacuum knot.
20. To unscrew three screws of fastening of a cover of the pump.
21. To uncover, a diaphragm, a spring, a washer and a shutter. To note shutter orientation.
22. To unscrew two screws of fastening and to remove эконостат.
23. Cautiously small screw-driver to release nylon clips and to disassemble эконостат.
24. To unscrew the central bolt of fastening of the chamber for a cooling liquid and to remove the chamber. Under a head of a bolt and on chamber perimetre ring consolidations are established.
25. On the case of a bimetallic spring and the holder of the lever заслонки there are labels. In the absence of labels it is necessary to put them. To unscrew three screws keeping a ring clip and to remove a clip and the case.
26. The holder of the lever заслонки can be removed from the carburettor case as with the bimetallic case and the chamber for a cooling liquid, and without them, after unscrewing of screws of fastening.
27. The vacuum device of a drive заслонки the secondary chamber can be removed after removal of the holder of the lever заслонки by moving of its roller emphasis and отжатия a star-shaped clip.