Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
- 14. An electric equipment
14.1. A technical characteristics
14.2. Safety locks and the relay
14.3. Electronic blocks of management
14.4. System of the central blocking
14.5. System of indexes of turns
14.6. The fuel computer
14.7. Additional control system
+ 14.8. The generator
- 14.9. A starter
14.9.1. Removal and starter installation
14.9.2. Dismantling and starter assemblage
14.9.3. Malfunctions of a starter
+ 14.10. A windscreen screen wiper, knot of indexes and a headlight
14.11. Removal and installation of a combination of devices
14.12. External and internal illumination
+ 14.13. An other electric equipment
+ 14.14. Electroschemes
|
Starter Bosch
|
1 – the case of the electromagnetic actuator,
2 – a spring,
3 – an anchor of the electromagnetic actuator,
4 – the lever,
5 – a rubber insert,
6 – a cover,
7 – the screw of fastening electromagnetic
The actuator,
8 – a lock ring,
9 – a ring,
10 – an anchor of a starter,
|
11 – the case of a starter,
12 – windings,
13 – the block of brushes of a collector,
14 – a cover of a collector,
15 – a sealing ring,
16 – a washer,
17 – a lock ring,
18 – a protective cover,
19 – a bolt of fastening of a protective cover,
20 – a coupling bolt of a starter |
The block of brushes of a collector of starter Bosch
|
|
1 – external contact,
2 – the plug |
Starter Bosch GF
|
1 electromagnetic actuator,
2 – a lining,
3 – a cover,
4 – contacts,
5 – the screw,
6 – a protective cover,
7 – a sealing ring,
8 – a lock ring,
9 – a washer,
10 – the plug,
11 – a cover of a collector,
12 – the holder of brushes of a collector,
13 – a winding conclusion статора,
14 – the case of a starter,
|
15 – a forward cover,
16 – the screw,
17 – the plug,
18 – an axial bolt of the lever,
19 – the lever,
20 – a coupling bolt of a starter,
21 – a spring of a clip of a brush,
22 – a brush,
23 – a collector,
24 – an anchor of a starter,
25 – приводная a gear wheel with обгонной муфтой,
26 – a ring,
27 – a lock ring |
Starter Bosch DW with a reducer
|
1 electromagnetic actuator,
2 – a spring,
3 – an anchor of the electromagnetic actuator,
4 – the lever,
5 – a forward cover,
6 – приводная a gear wheel with обгонной муфтой,
7 – a lining,
8 – an external gear wheel of a reducer,
9 – a power shaft with planetary
Gear wheels,
10 – a lock ring,
|
11 – a coupling bolt of a starter,
12 – a protective cover,
13 – a lock ring,
14 – a ring,
15 – a plate,
16 – the holder of brushes of a collector,
17 – the case of a starter,
18 – a rubber lining,
19 – an anchor of a starter,
20 – a cover |
Starters Lucas
|
1 – a head,
2 – knot of a drive,
3 – the lever of a drive,
4 – the electromagnetic switch,
|
5 – статор,
6 – a rotor,
7 – a back cover with
щеткодержателем |
Starter Cajavec
|
1 – a head,
2 – knot of a drive,
3 – the lever of a drive,
4 – the electromagnetic switch,
|
5 – статор,
6 – a rotor,
7 – щеткодержатель |
Starter Nippondenso
|
1 – a head,
2 – knot of a drive,
3 – the lever of a drive,
4 – the electromagnetic switch,
|
5 – статор,
6 – a rotor,
7 – щеткодержатель |
After starter dismantling it is necessary to check up:
– A condition of brushes, their deterioration, and also freedom of moving of brushes in щеткодержателях;
– Force of a clip and position of springs of brushes;
– A kind of a collector which should be cleared a rag moistened in gasoline or трихлорэтилене, and прошлифовать a fine-grained emery paper;
– A condition of plugs of self-greased bearings; in case of need replacements should be lowered new plugs not less than for 20 minutes in engine oil (viscosity SAE 30 or 40) before their installation in a starter.
Check of the electromagnetic actuator
| PERFORMANCE ORDER |
| 1. To disconnect a wire of weight from the accumulator and all wires from the electromagnetic actuator. |
|
2. To connect the accumulator with consistently included control bulb capacity of 3 Vt to the case and a socket of a food of a winding of the electromagnetic actuator (1 – carving contact for connection of a wire from the accumulator, 2 – carving contact to the starter electric motor, 3 – a socket of a food of a winding electromagnetic
The actuator). |
| 3. In the absence of breakage of a winding the bulb should burn. |
|
4. For check of contacts of inclusion of a starter to connect the accumulator with consistently included control bulb capacity of 12-21 Vt to carving contacts of the electromagnetic actuator and an additional wire to a socket of a food of a winding of the electromagnetic actuator (1 – carving contact for connection of a wire from the accumulator, 2 – carving contact to the starter electric motor, 3 – a socket of a food of a winding of the electromagnetic actuator). |
| 5. At connection of an additional wire to a socket of a food of a winding of the electromagnetic actuator should work the electromagnetic actuator and light up a bulb. |
|
|
|
