FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
- 14. An electric equipment
   14.1. A technical characteristics
   14.2. Safety locks and the relay
   14.3. Electronic blocks of management
   14.4. System of the central blocking
   14.5. System of indexes of turns
   14.6. The fuel computer
   14.7. Additional control system
   + 14.8. The generator
   + 14.9. A starter
   + 14.10. A windscreen screen wiper, knot of indexes and a headlight
   14.11. Removal and installation of a combination of devices
   14.12. External and internal illumination
   - 14.13. An other electric equipment
      14.13.1. Removal and installation of switches, engines and gauges
      14.13.2. Additional control system
      14.13.3. Removal and radio receiver installation
      14.13.4. Removal and installation of loudspeakers
      14.13.5. System of the anticreeping alarm system
   + 14.14. Electroschemes


b087f616

14.13.1. Removal and installation of switches, engines and gauges

LIGHT SWITCH, THE SWITCH OF THE FAN OF THE HEATER

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
2. To remove the switch handle, having pulled it on itself.
3. To wring out two clamps, to take the switch from the instrument panel.
4. To disconnect a socket and to remove the switch.
5. Installation is made in sequence, return to removal.

REGULATOR OF LIGHT EXPOSURE OF DEVICES

PERFORMANCE ORDER
1. To unscrew four screws and to remove a decorative overlay of a combination of devices.
2. To take a regulator of light exposure of devices (it is specified by an arrow) and to disconnect a socket.
3. In case of malfunction the regulator of light exposure of devices is not under repair, and is subject to replacement.

THE SWITCH OF MANAGEMENT OF POSITION OF THE MIRROR AND THE SWITCH ELECTRIC СТЕКЛОПОДЪМНИКОВ

PERFORMANCE ORDER
1. A screw-driver with a thin edge to hook the switch and to take it from an armrest.
2. To disconnect a socket and to remove the switch (it is specified by an arrow).
3. Installation is made in sequence, return to removal.

THE SWITCH OF INDEXES OF TURNS AND THE SWITCH OF CLEANERS AND WINDSCREEN WASHERS

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
2. To remove the central overlay of a steering wheel.
3. To remove the top and bottom casings of a steering column, preliminary having unscrewed six screws of fastening.
4. To unblock a steering wheel and to turn it so that access to two screws (are specified by arrows), крепящим the switch has opened. To unscrew screws.
5. To take the switch from a steering column and to disconnect a socket.
6. At installation to check up switch action before establishing casings of a steering column and the central cover of a steering wheel.

THE SWITCH OF INDIVIDUAL ILLUMINATION ON THE RACK OF DOORS

PERFORMANCE ORDER
1. To unscrew one screw and to take the switch.
2. To fix wires a thread or a clothespin so that they did not fail in a rack and after that to disconnect a socket.
3. Before installation to grease a point of turn of the button of the switch with technical vaseline.

THE SWITCH OF LIGHT OF THE BACKING (MANUAL TRANSMISSION)

The switch of light of a backing is on the right party of a transmission.

PERFORMANCE ORDER
1. To lift and fix on supports a forward part of the car.
2. To remove from the switch a wire, carefully to clear the switch and a place adjoining to the switch, and to unscrew the switch.
3. After switch installation to check up that the switch wire is located on sufficient removal from an exhaust pipe.

THE SWITCH OF OPENING OF THE HATCH

PERFORMANCE ORDER
1. Being careful, a screw-driver with a thin edge to take out the switch from the top console.
2. To disconnect a socket and to remove the switch.

THE GAUGE OF INCLUSION OF THE MANUAL BRAKE

PERFORMANCE ORDER
1. To remove a rubber cover and, at necessity, the central console or the decorative panel of the gauge.
2. To remove from the gauge a wire.
3. To unscrew two screws and to remove the gauge.

THE STOPLIGHT SWITCH

PERFORMANCE ORDER
1. To remove an upholstery under the panel of devices from outside the driver, fixed by plastic clips.
2. To remove from the wire switch.
3. To turn the switch on 90 ° counter-clockwise and to remove it with скобы fastenings of a pedal of a brake.
4. At installation to press a pedal against the stop, to insert the switch and to turn clockwise for its fixing. To release a pedal and to check up, that at least 2 mm of a rod of the switch were visible.

THE GAUGE OF PRESSURE OF OIL

The gauge of pressure of oil on all engines, except DOHC, is located on a left-hand side of the block of cylinders. On engines DOHC the gauge of pressure of oil is located on a forward left-hand side of the block of cylinders.

PERFORMANCE ORDER
1. For simplification of access to the gauge to displace aside one of pipelines.
2. To remove from the wire switch.
3. To unscrew and remove the gauge.
4. Before installation carefully to smooth out the gauge and its nest. On a gauge carving to apply a thin film hermetic.
5. To establish the gauge, to connect wires, to start the engine and to check up tightness of installation of the gauge.
6. To stop the engine and to check up engine oil level.

THE SWITCH OF THE HEATER OF BACK GLASS

PERFORMANCE ORDER
1. To unscrew four screws and to remove a decorative overlay of a combination of devices.
2. Being careful, an edge of a thin screw-driver to take the switch from a nest.
3. To remove from the switch a socket.

THE SWITCH OF ADJUSTMENT OF POSITION OF THE FORWARD SEAT

PERFORMANCE ORDER
1. To remove the panel of a covering of a seat.
2. A screw-driver with a thin edge to remove from the switch of the handle of management.
3. To unscrew two screws of fastening, to take the switch and to disconnect it.

THE ENGINE OF SYSTEM OF THE CENTRAL BLOCKING

System of the central blocking of doors


The lock of closing of a back door with an electromagnet


PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator and to open all doors.
2. To remove an internal upholstery of a door.
3. Being careful, to remove from a door isolating covering of a door in the field of installation of the engine of system of the central blocking.
4. To unscrew two screws (fastenings of the engine are specified by arrows) and to disconnect the engine from a rod of management of the lock.
5. To remove an electric socket.
6. To remove the electric motor. In case of malfunction of the engine it is necessary to replace it, as it is not subject to repair.
7. Installation is made in sequence, return to removal, and it is obligatory to establish the button of blocking of doors in position "openly", to weaken the screw of fastening of the internal handle, to shift the handle forward against the stop and to tighten the screw.

THE ENGINE OF DRIVE СТЕКЛОПОДЪЕМНИКА

PERFORMANCE ORDER
1. To remove the mechanism of lifting of glass together with the engine.
2. To check up that the spring keeps the lever in final position (marksman).
3. To unscrew three bolts (are specified by arrows) and to separate the engine from the mechanism of lifting of glass.

The prevention

Careless отпускание springs it can appear the reason of damages and wounds.


4. Installation is made in sequence, return to removal.

THE ENGINE OF ADJUSTMENT OF POSITION OF THE SEAT, ENGINES OF LIFTING AND MOVING OF THE PILLOW OF THE SEAT

PERFORMANCE ORDER
1. To shift a forward seat back against the stop.
2. To unscrew two bolts of fastening from a forward part of a frame of a seat and to reject a seat back.
3. To unscrew on two bolts (are specified by arrows) and to remove electric motors.
4. To check up that cables of a drive from worm gears move without effort, otherwise to disconnect also one end of a worm gear.
5. At removal only one engine take it ножевые contacts from the general socket after removal of the case of a socket.
6. Installation is made in sequence, return to removal.

THE ENGINE OF CHANGE OF THE INCLINATION OF THE BACK OF THE SEAT

PERFORMANCE ORDER
1. To remove a forward seat.
2. To unscrew two bolts of fastening, to disconnect a socket and to take the electric motor from the rejecting mechanism.
3. The engine to establish so that the gear gear wheel of the electric motor was hooked with a gear wheel of the mechanism of a deviation.
4. To connect a socket and to fix the electric motor two bolts.
5. The further installation is made in sequence, return to removal.

THE ELECTRIC MOTOR OF THE DRIVE OF THE HATCH

PERFORMANCE ORDER
1. To remove the top console.
2. To unscrew three bolts of fastening (are specified by arrows), to lower the electric motor, to disconnect a socket and to take the relay.
3. The engine to establish so that the gear gear wheel of the electric motor was hooked with a gear wheel of the mechanism of management of position of a cover of the hatch.
4. To establish the relay, to connect a socket and to fix the electric motor three bolts.

THE SPEEDOMETER GAUGE

 
1 – a brown wire,
2 – a brown wire with a yellow strip,
3 – a brown wire with a black strip,
4 – contact of grounding,
5 – изоляционная a tube,
6 – a place of cutting of a brown wire

The speedometer drive is carried out from the electric gauge located on a left-hand side of lengthening of a transmission.

PERFORMANCE ORDER
1. To lift and fix a forward part of the car.
2. Under the gauge to establish the corresponding container.
3. To unscrew a fastening bolt (it is specified by an arrow) and to take the gauge from a transmission (1 – a mechanical transmission, 2 – an automatic transmission).
4. To disconnect an electric socket.
5. At installation of the new gauge to establish on it from the old gauge приводную a gear wheel and a ring clip, and on models with automatic transmission and a sealing ring.
6. If on the old gauge was two wires, and on new three, a brown wire to cut off from a socket and in addition to establish grounding.
7. To establish the new gauge and to fix it by means of a new bolt (М6х25 mm for a manual transmission and М6х35 mm for an automatic transmission). Except the new gauge, a bolt also крепит a new ear of grounding, the tyre of grounding of a radio receiver and fixing скобу a socket.
8. To connect a socket and to fix it on скобе.
9. To finish oil level in a transmission to norm.

LAMP OF ILLUMINATION OF THE FUEL COMPUTER

PERFORMANCE ORDER
The cars made till 04.1992
1. To remove a decorative casing of the instrument panel which fastens four screws.
2. Cautiously to take the fuel computer. To remove a socket, having pressed it downwards.
3. To take a cartridge with a bulb, having compressed it пассатижами and having turned counter-clockwise. To extend from a cartridge an old bulb.
4. Installation of a new bulb is made in sequence, return to removal.
The cars made since 04.1992
5. To remove a decorative casing of the instrument panel which fastens two screws and two clips.
6. To take a regulator of light exposure of devices and to disconnect a socket.
7. To remove three handles of management of a heater for access to screws of fastening of the panel of a heater.
8. To unscrew four screws of fastening of the panel of a heater and partially to displace the panel.
9. To disconnect from the panel sockets of a heater of glass and the fuel computer and to remove the panel.
10. To unscrew four screws (computer fastenings to the panel are specified by arrows) and to remove the computer.
11. To replace lamps of illumination of the fuel computer.

THE GAUGE OF THE STREAM OF FUEL (ONLY CARBURETTOR MODELS)

The gauge is located on the left mudguard in a motor compartment.

PERFORMANCE ORDER
1. To remove an occasion of weight from the accumulator.
2. To remove from the gauge an electric socket and fuel tubes.
3. To unscrew three screws of fastening скобы the gauge. To remove the gauge together with скобой.
4. Gauge installation is made in sequence, return to removal.