| 1. Turning a cranked shaft for the central bolt of fastening гасителя крутильных fluctuations, to establish the piston of 1 cylinder in an ignition point (12 ° before ВМТ). Correctness of installation can be checked up, having uncovered the ignition distributor, thus the distributor rotor should be combined with contact of a high-voltage wire going to the cylinder number 1. |
| 2. To remove a wire of weight from the accumulator. |
| 3. To uncover the air filter together with the gauge of a stream of air and hoses. |
| 4. To uncover маслозаливной mouths. |
| 5. To merge cooling liquid from cooling system. |
| 6. To disconnect a hose of connection of the water pump and a broad tank. |
|
|
| 7. To remove the top casing of a radiator and a radiator. |
| 8. To remove the fan from a nave of the water pump. |
The prevention The nut of fastening of the fan has the left carving.
|
| 9. To disconnect hoses of system of cooling from unions of the water pump. |
| 10. To unscrew a bolt of fastening of a suspension bracket of a hose of system of cooling from a forward cover. |
| 11. To remove auxiliary приводной a belt. |
| 12. To unscrew 4 bolts and to remove a pulley of a cranked shaft. |
|
|
| 13. To block a cranked shaft for a gear wreath of a flywheel, to unscrew the central bolt of fastening гасителя крутильных fluctuations and to remove it, using a special stripper. |
| 14. To merge engine oil from the engine. |
| 15. To disconnect wires, to unscrew and remove a starter. |
|
16. Being careful, the load-lifting mechanism to raise the engine, and then to unscrew holders of the engine. |
| 17. To check up that the steering wheel is established in movement position directly forward and a paint or a marker to note position of the bottom collar of an intermediate shaft and a gear wheel of steering transfer, then to disconnect an intermediate shaft from steering transfer. |
| 18. To disconnect brake tubes from a beam of a forward suspension bracket. |
| 19. To prop up a beam by means of the corresponding lift and a wide board. |
| 20. To unscrew bolts of fastening of a beam to the car bottom. To incline a beam so that access to oil картеру was released. |
| 21. To unscrew bolts and nuts of fastening oil картера and to take it from under the engine. |
| 22. To unscrew 9 bolts of fastening of a cover of the mechanism timing and to uncover together with the water pump. |
|
23. To check up that labels (are specified by arrows) on asterisks are directed to each other. Otherwise to tighten a cranked shaft before combination of labels. |
| 24. To unscrew and remove натяжитель chains of a drive of the mechanism timing. |
| 25. To fix an asterisk of a camshaft and to unscrew a bolt of fastening of an asterisk. |
| 26. To remove a camshaft asterisk together with a chain and to remove a chain from an asterisk of a cranked shaft. |
| 27. If necessary to remove from a cranked shaft an asterisk with шпонкой and directing to a chain. |
| 28. Carefully to clear interfaced surfaces of traces of old linings. |
|
29. To check up position шпоночных grooves on distributive and cranked shaft. They should be directed to each other. |
| 30. To establish on a cranked shaft directing chains and an asterisk with шпонкой. |
| 31. To establish a chain on an asterisk of a cranked shaft. |
| 32. To establish a chain on an asterisk of a camshaft and to establish an asterisk together with a chain on a camshaft, thus шпонка a camshaft should enter into an asterisk groove. |
| 33. To screw up a bolt of fastening of an asterisk of a camshaft. |
| 34. To compress натяжитель chains for what to press плунжер натяжителя and to keep it in this condition, having adhered a corresponding tape. |
| 35. To establish натяжитель chains into place, thus having removed a tape keeping плунжер. |
| 36. To establish a lining of a forward cover of the mechanism timing. |
| 37. To replace a sealing ring of a forward cover of the mechanism timing. |
| 38. To establish a forward cover of the mechanism timing. |
|
39. To centre an aperture in a cover concerning a cranked shaft, and also to level in relation to a plane of installation oil картера. |
|
40. To screw bolts of fastening of a forward cover of the mechanism timing (are specified by arrows). |
| 41. Carefully to clear interfaced surfaces of the block of cylinders and oil картера. |
| 42. To establish a new lining in flutes oil картера. |
| 43. To put hermetic on forward and back sites oil картера. |
| 44. To put the structure interfering unscrewing on a carving of bolts, to establish oil картер and to screw up bolts. |
| 45. To grease with engine oil working edges of a sealing ring and a surface interfaced to a ring гасителя крутильных fluctuations and to establish гаситель on a cranked shaft. |
| 46. To screw up the central bolt of fastening гасителя крутильных fluctuations by the corresponding moment. |
| 47. To establish a pulley of a cranked shaft. |
| 48. To establish a beam and brake tubes. |
| 49. To connect an intermediate shaft to steering transfer. |
| 50. To establish a starter and to connect wires. |
| 51. To establish auxiliary приводной a belt. |
| 52. To establish the fan and a radiator. |
| 53. To establish a cover of the air filter. |
| 54. To fill in in the engine engine oil and cooling liquid in system of cooling of the engine. |
