FORD SCORPIO

1985-1994 of release

Repair and car operation


Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   - 3.2. Engine DOHC
      3.2.1. A technical characteristics
      + 3.2.2. The repair which is not demanding removal of the engine
      + 3.2.3. Removal and installation of the engine without a transmission
      3.2.4. Ventilation system картера
      - 3.2.5. Greasing system
         3.2.5.1. Removal and installation oil картера
         3.2.5.2. Removal and installation of the oil pump
         3.2.5.3. Dismantling of the oil pump
   + 3.3. Engine V6
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


b087f616

3.2.5. Greasing system

3.2.5.1. Removal and installation oil картера
THE GENERAL DATA

Elements of system of greasing

1 – the gauge of pressure of oil,
2 – the oil filter,
3 – a pipe of a measuring instrument of level of oil,
4 – a measuring instrument of level of oil, 		5 – a lining of the oil pallet,
6 – the oil pallet,
7 – маслосливная a stopper

Removal

PERFORMANCE ORDER
1. To remove a transmission.
2. To remove coupling.
3. To remove a flywheel and a protective guard of the engine.
4. To merge engine oil of their engine.
5. To check up that the steering wheel is established in movement position directly forward and a paint or a marker to note position of the bottom collar of an intermediate shaft and a gear wheel of steering transfer, then to disconnect an intermediate shaft from steering transfer.
6. Being careful, the load-lifting mechanism to raise the engine, and then to unscrew holders of the engine.
7. To disconnect brake tubes from a beam of a forward suspension bracket.
8. To prop up a beam by means of the corresponding lift and a wide board.
9. To unscrew bolts of fastening of a beam to the car bottom. To incline a beam so that access to oil картеру was released.
10. To unscrew bolts and nuts of fastening oil картера and to take it from under the engine.

Installation

Places of drawing of hermetic on interfaced surfaces oil картера and the block of cylinders

2 – places of drawing of hermetic

PERFORMANCE ORDER
1. Carefully to clear interfaced surfaces of the block of cylinders and oil картера.
2. To establish a new lining in flutes oil картера.
3. To put hermetic on the sites interfaced to a cover of a sealing ring.
4. To put the structure interfering unscrewing, on a carving of bolts and nuts, to establish oil картер and to screw up bolts and nuts without tightening them it is definitive.
5. To level face surfaces oil картера and the block of cylinders and to tighten definitively bolts and nuts. If between face surfaces there is a step, it is necessary to measure it and depending on step size to establish a lining of a recommended thickness.
6. The further operations are made in sequence, return to removal.

Step size
Thickness
Colour of an established lining
0 – 0,25 mm
Lining not to establish
0,25 – 0,29 mm
0,15 mm
The silver
0,30 – 0,44 mm
0,30 mm
Dark blue
0,45 – 0,59 mm
0,45 mm
The red
0,60 – 0,75 mm
0,60 mm
The black